strut top-drivers side
- sageman
- Knows how to use the parking brake
- Posts: 198
- Joined: Sat Sep 16, 2017 5:07 pm
- Location: norwich
strut top-drivers side
first my passenger side was found to have completely failed while at pleides who sourced and fitted a good one
now my drivers side has failed the two parts separating entirely one rattling about inside the other this is the same failure type on both sides
needles to say i need another
however with all the different types im not sure which i have and going off year is not garenteed as at some point in the past this same drivers side had suffered a full 'punch through' failure and i have no idea if everything was replaced with the correct parts or not
i seem to remember reading there is different amounts of dots to determine which type it is
mine has 6
or am i getting confused here with reliant gearboxes which ARE distinguished from a number of dots on the rear and the dots have no bearing on which strut top i have
i did take some photos unfortunately the camera on this phone is damaged and were nowhere near clear enough
now my drivers side has failed the two parts separating entirely one rattling about inside the other this is the same failure type on both sides
needles to say i need another
however with all the different types im not sure which i have and going off year is not garenteed as at some point in the past this same drivers side had suffered a full 'punch through' failure and i have no idea if everything was replaced with the correct parts or not
i seem to remember reading there is different amounts of dots to determine which type it is
mine has 6
or am i getting confused here with reliant gearboxes which ARE distinguished from a number of dots on the rear and the dots have no bearing on which strut top i have
i did take some photos unfortunately the camera on this phone is damaged and were nowhere near clear enough
1976 Reliant kitten
1985 Reliant fox Tandy campervan
1998 Peugeot 306 GTI-6
h̶o̶p̶e̶f̶u̶l̶l̶y̶ ̶a̶n̶ ̶X̶M̶ ̶o̶n̶e̶ ̶d̶a̶y̶
1993 XM sei V6 RP 5876
1985 Reliant fox Tandy campervan
1998 Peugeot 306 GTI-6
h̶o̶p̶e̶f̶u̶l̶l̶y̶ ̶a̶n̶ ̶X̶M̶ ̶o̶n̶e̶ ̶d̶a̶y̶
1993 XM sei V6 RP 5876
-
- Global Moderator
- Posts: 13785
- Joined: Thu Jun 18, 2009 6:44 pm
Re: strut top-drivers side
There are three types of hydractive strut tops.
Very early ones, straight sides to the upper casting and four spreading punchings to the lower tube.
Later 16mm holed ones, stepped upper casting, 10 punchings.
Later still, 18mm hole, stepped casting, 10 punchings.
Measure the diameter of the threaded section of strut to ascertain which you have.
What has happened is the steel on the underside of the plate has corroded, thus the rubber to steel bond has failed due to the surface of the steel coming away.
The surface corrosion is only a few microns thick, but the oxide has parted company with the rest of the surface.
Theoretically, as long as the rubber isn't torn the steel and rubber could be cleaned up and abraded, then re-bonded.
Very early ones, straight sides to the upper casting and four spreading punchings to the lower tube.
Later 16mm holed ones, stepped upper casting, 10 punchings.
Later still, 18mm hole, stepped casting, 10 punchings.
Measure the diameter of the threaded section of strut to ascertain which you have.
What has happened is the steel on the underside of the plate has corroded, thus the rubber to steel bond has failed due to the surface of the steel coming away.
The surface corrosion is only a few microns thick, but the oxide has parted company with the rest of the surface.
Theoretically, as long as the rubber isn't torn the steel and rubber could be cleaned up and abraded, then re-bonded.
92 2.1SED M.RP5740 ECZ Sable Phenicien
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White
- White Exec
- Citroen God!
- Posts: 6642
- Joined: Fri Mar 11, 2011 7:38 pm
- Orga / RP numbers: RP7165
1996 2.5TD saloon, Exclusive, Polar White
1992 BX19D Millesime, Sable Phenicien - Location: ex-Ealing, Cheshire, W.Sussex & Surrey. Now living in Sayalonga (Malaga, Spain)
Re: strut top-drivers side
The diameter to measure is the top hole in the strut top, which isn't itself threaded. It's the top end of the securing taper.
It's the tip of the strut rod that is threaded (where the nut goes).
Be sure to specify car-left or car-right when ordering replacement tops, as they are 'handed'.
Will,
Do we have any confirmation that re-bonding of untorn rubber to the existing steel is effective and durable?
Who is offering this as a service?
It's the tip of the strut rod that is threaded (where the nut goes).
Be sure to specify car-left or car-right when ordering replacement tops, as they are 'handed'.
Will,
Do we have any confirmation that re-bonding of untorn rubber to the existing steel is effective and durable?
Who is offering this as a service?
Chris
1996 XM 2.5TD Exclusive RP7165 Polar White
1992 BX19D Millesime RP5800 Sable
1989 BX19RD Delage Red Deceased; 1998 ZX 1.9D Avantage auto Triton Green Company car 1998..2001; 2001 Xantia 1.8i auto Wicked Red Company car 2001..2003
1996 XM 2.5TD Exclusive RP7165 Polar White
1992 BX19D Millesime RP5800 Sable
1989 BX19RD Delage Red Deceased; 1998 ZX 1.9D Avantage auto Triton Green Company car 1998..2001; 2001 Xantia 1.8i auto Wicked Red Company car 2001..2003
-
- Global Moderator
- Posts: 13785
- Joined: Thu Jun 18, 2009 6:44 pm
Re: strut top-drivers side
One last thing to note is whether the the projection underneath is long, or short skirt, which is pretty obvious when you look at them.
I think only later, 18mm holed types have longer skirts, both 16mm types are short skirted.
The length of skirt is just for the gaiter to clip onto, so not imperative.
As far as rebonding, no-one offers it as a service, but some members have performed this to their own.
The issue is finding a suitable bonding agent, windscreen Pu adhesive has been used, but I believe a solvent rubber cement might work better.
I think only later, 18mm holed types have longer skirts, both 16mm types are short skirted.
The length of skirt is just for the gaiter to clip onto, so not imperative.
As far as rebonding, no-one offers it as a service, but some members have performed this to their own.
The issue is finding a suitable bonding agent, windscreen Pu adhesive has been used, but I believe a solvent rubber cement might work better.
92 2.1SED M.RP5740 ECZ Sable Phenicien
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White
- sageman
- Knows how to use the parking brake
- Posts: 198
- Joined: Sat Sep 16, 2017 5:07 pm
- Location: norwich
Re: strut top-drivers side
![Image](https://live.staticflickr.com/65535/51529109536_7740ef2539_k.jpg)
![Image](https://live.staticflickr.com/65535/51529814719_d125edd7e8_k.jpg)
![Image](https://live.staticflickr.com/65535/51529817024_a8290ba897_k.jpg)
1976 Reliant kitten
1985 Reliant fox Tandy campervan
1998 Peugeot 306 GTI-6
h̶o̶p̶e̶f̶u̶l̶l̶y̶ ̶a̶n̶ ̶X̶M̶ ̶o̶n̶e̶ ̶d̶a̶y̶
1993 XM sei V6 RP 5876
1985 Reliant fox Tandy campervan
1998 Peugeot 306 GTI-6
h̶o̶p̶e̶f̶u̶l̶l̶y̶ ̶a̶n̶ ̶X̶M̶ ̶o̶n̶e̶ ̶d̶a̶y̶
1993 XM sei V6 RP 5876
- sageman
- Knows how to use the parking brake
- Posts: 198
- Joined: Sat Sep 16, 2017 5:07 pm
- Location: norwich
Re: strut top-drivers side
I have measured the top hole at 16mm so this must be the common type with the short skirt
Is this correct
Is this correct
1976 Reliant kitten
1985 Reliant fox Tandy campervan
1998 Peugeot 306 GTI-6
h̶o̶p̶e̶f̶u̶l̶l̶y̶ ̶a̶n̶ ̶X̶M̶ ̶o̶n̶e̶ ̶d̶a̶y̶
1993 XM sei V6 RP 5876
1985 Reliant fox Tandy campervan
1998 Peugeot 306 GTI-6
h̶o̶p̶e̶f̶u̶l̶l̶y̶ ̶a̶n̶ ̶X̶M̶ ̶o̶n̶e̶ ̶d̶a̶y̶
1993 XM sei V6 RP 5876
-
- Global Moderator
- Posts: 13785
- Joined: Thu Jun 18, 2009 6:44 pm
Re: strut top-drivers side
Torn rubber...there's no saving that other than a rebuild.
It looks like a 16mm strut and short skirt, to me.
It looks like a 16mm strut and short skirt, to me.
92 2.1SED M.RP5740 ECZ Sable Phenicien
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White
-
- Global Moderator
- Posts: 9987
- Joined: Wed Apr 15, 2009 9:11 am
- Location: North Wales - FAR far far away!!! :-p
Re: strut top-drivers side
Are you looking for a replacement top. I've a number in my shed with various piston sizes. I'd need an overhead view of the top to compare.
Projects:(eventually if theres any bodywork left)
93 L Xm 2.1t D auto project
93 L xm V6 12v Sei Manual
Others
In use.. 1995 M reg S2 2.1td auto exclusive
93 L Xm 2.1t D auto project
93 L xm V6 12v Sei Manual
Others
In use.. 1995 M reg S2 2.1td auto exclusive
-
- Global Moderator
- Posts: 13785
- Joined: Thu Jun 18, 2009 6:44 pm
Re: strut top-drivers side
Sageman has measured the top hole at 16 mm, so small hole.
It's right side, so the sphere connector is facing the left of centre compared to the plate, when viewed from above.
92 2.1SED M.RP5740 ECZ Sable Phenicien
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White
- sageman
- Knows how to use the parking brake
- Posts: 198
- Joined: Sat Sep 16, 2017 5:07 pm
- Location: norwich
Re: strut top-drivers side
Can anybody help with this please
I am still in need of one..
I am still in need of one..
1976 Reliant kitten
1985 Reliant fox Tandy campervan
1998 Peugeot 306 GTI-6
h̶o̶p̶e̶f̶u̶l̶l̶y̶ ̶a̶n̶ ̶X̶M̶ ̶o̶n̶e̶ ̶d̶a̶y̶
1993 XM sei V6 RP 5876
1985 Reliant fox Tandy campervan
1998 Peugeot 306 GTI-6
h̶o̶p̶e̶f̶u̶l̶l̶y̶ ̶a̶n̶ ̶X̶M̶ ̶o̶n̶e̶ ̶d̶a̶y̶
1993 XM sei V6 RP 5876