Wanted: Hydractive electrovalve wiring loom connector.

Selling off one (or bits :o) of your XM collection, or perhaps searching for those elusive headlight washer covers? This is the place to do it.
Post Reply
Dieselman
Global Moderator
Posts: 13734
Joined: Thu Jun 18, 2009 6:44 pm

Wanted: Hydractive electrovalve wiring loom connector.

Post by Dieselman » Sat Oct 30, 2021 9:57 am

Wanted:

Electrovalve wiring loom connectors (male and female) and short lengths of wire, from a H/a loom for Hydractive 2 car.

This is the connector that is situated on the right strut tower under the sphere.

I should have one for H1 system, but if anyone has one on a scrap loom, that might be useful also.
92 2.1SED M.RP5740 ECZ Sable Phenicien
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White

citroenxm
Global Moderator
Posts: 9981
Joined: Wed Apr 15, 2009 9:11 am
Location: North Wales - FAR far far away!!! :-p

Re: Wanted: Hydractive electrovalve wiring loom connector.

Post by citroenxm » Sat Oct 30, 2021 5:13 pm

Not sure what you mean will.. I've a. Number of looms from cars.. Sadly no spare cars. Anymore Nd no doubt what you wanted was on the last car that wentast month..
Projects:(eventually if theres any bodywork left)
93 L Xm 2.1t D auto project
93 L xm V6 12v Sei Manual

Others
In use.. 1995 M reg S2 2.1td auto exclusive

Dieselman
Global Moderator
Posts: 13734
Joined: Thu Jun 18, 2009 6:44 pm

Re: Wanted: Hydractive electrovalve wiring loom connector.

Post by Dieselman » Sun Oct 31, 2021 7:10 am

I want to make a pass through loom, so need both connectors and the wires to solder together.

The intention is to use it as a break out loom for testing H/a operation, by adding some Led's and test points.

H/a1 and H/a2 need a different loom due to the additional electrovalve on H/a2.

Another way would be a breakout at the H/a Ecu, but that would need the connectors from a scrap Ecu and the loom connectors.

I've never known a H/a Ecu fail, so don't have a scrap one.
92 2.1SED M.RP5740 ECZ Sable Phenicien
92 3.0 V6-24.Rp 5713 EXY Black
92 2.1SD M.RP 5685 ENT Blue Sideral
Prev
90 2.1SD M.RP 5049 EJV Mandarin
92 2.1SD A.RP 5698 EJV Mandarin
94 2.1SD A.RP 6218 ERT Triton Green
91 2.0SI M.RP 5187 EWT White

citroenxm
Global Moderator
Posts: 9981
Joined: Wed Apr 15, 2009 9:11 am
Location: North Wales - FAR far far away!!! :-p

Re: Wanted: Hydractive electrovalve wiring loom connector.

Post by citroenxm » Sun Oct 31, 2021 7:13 am

I've plenty of ecus.. The suspension loom was still on the last car to go too.

I have S1 looms from the two early cars I stripped bare about 4 years ago or so. I'll come across them or may have already without realising it. I'll check the looms boxes at the unit this week as little man is back to school tomorrow..
Projects:(eventually if theres any bodywork left)
93 L Xm 2.1t D auto project
93 L xm V6 12v Sei Manual

Others
In use.. 1995 M reg S2 2.1td auto exclusive

Post Reply