Citroen XM Forum

xantia_v6 wrote:Adding to the list a fuel sender fixing ring (I presume that XM and Xantia are all the same). I managed to break mine today. I will be at the event next Sunday, if someone could look one out.

xantia_v6 wrote:I am trying to keep my car in pristine condition, and there are a few small parts that I would like to get hold of, or spares for the future.

I will put a list here and update this first post as the list shrinks (or grows).

The car is a 1999 24V V6 ES9 LHD Exclusive Manual transmission in Quartz grey.

Bits for inside:
- Plastic hinge pin(s) for the internal rear window. COULD BE PRESUADED TO FIND A COUPLE BUT THEN MY SET MIGHT BE SHORT NEED TO CHECK STOCKS...
- Original factory-fit over-mats (grey), particularly front left and rear both sides.

Bits under the bonnet:
- Right hand ES9 V6 engine mount (complete or rubber donut).
- Headlight wiring harness (1997-on RHD or LHD), Scandinavian spec. with daytime running lights would be nice.
- Screen wash level sensor YES I THINK I HAVE ONE SOMEWHERE

Exterior bits:
- any of the detachable plastic trim parts painted in Silver Quartz (mirror covers, scuttle end pieces bumpers etc) in near perfect condition.
- at least one door rubbing strip with a piece of perfect trim to cut down to repair the trim on a front wing. DO YOU WANT A WING TRIM AS IS? CAN DO ONE IN BASE SPEC GREY IF SO? Is it the Crome your after?
- a rubber seal for the hatchback tailgate in good condition. SHOULD HAVE ONE. ILL CHECK TWO THAT I KNOW ARE BUT OTHERS I HAVE NO IDEA

Any other ES9-specific parts that might come in handy one day...

PM me if you have any of the above to spare.

citroenxm wrote:

xantia_v6 wrote:Adding to the list a fuel sender fixing ring (I presume that XM and Xantia are all the same). I managed to break mine today. I will be at the event next Sunday, if someone could look one out.

The large Screw Item that holds the Pump/Level sender in place???

xantia_v6 wrote: - Plastic hinge pin(s) for the internal rear window.

citroenxm wrote: COULD BE PRESUADED TO FIND A COUPLE BUT THEN MY SET MIGHT BE SHORT NEED TO CHECK STOCKS...

xantia_v6 wrote: - Screen wash level sensor

citroenxm wrote: YES I THINK I HAVE ONE SOMEWHERE

- at least one door rubbing strip with a piece of perfect trim to cut down to repair the trim on a front wing. DO YOU WANT A WING TRIM AS IS? CAN DO ONE IN BASE SPEC GREY IF SO? Is it the Crome your after?

xantia_v6 wrote: - a rubber seal for the hatchback tailgate in good condition.

citroenxm wrote: SHOULD HAVE ONE. ILL CHECK TWO THAT I KNOW ARE BUT OTHERS I HAVE NO IDEA
.

kingp wrote:Mike you basically want an es9 engine in decent order don't you

The engine mount can possibly be redone using the engine mount from the rear of the engine as a base...

xantia_v6 wrote:
A complete engine might be a bit much...

I think the lower mount is made from a harder compound rubber. so would not have the same performance. It should be possible to get the rubber re-cast to the original specification, but I don't currently know of a suitable supplier (I knew a company that did this, but they went out of business).

Dieselman wrote:

xantia_v6 wrote:
A complete engine might be a bit much...

I think the lower mount is made from a harder compound rubber. so would not have the same performance. It should be possible to get the rubber re-cast to the original specification, but I don't currently know of a suitable supplier (I knew a company that did this, but they went out of business).

http://www.elastomer.eu/index.php?lang=lt will do it for you.