At 12.30 today I got a phone call from the freight forwarding agent down in Southampton who were doing the customs clearance advising me that everything was sorted and that the final fee was £250. MSC charged another £50 to move the container on the port. Total shipping costs have worked out to be around £2750.
I was a little disheartened at this point as I seem to have started collecting £50 charges from the Port authorities!
At 13:20 I got a call from Forth Ports advising that all the clearance was sorted and that I was able to start the 46 mile journey to the port to collect the car from the container.
At 14:30 we arrived at the port. We all had to have high visibility vests with us and we all needed photographic ID to gain access to the port. Once we were through security we followed the road for about a mile into the Port and were pointed towards a big shed with F written on the wall.
When we pulled up outside in the Range Rover there were 3 port staff waiting there for us. They cut the seal off the container with a huge pair of bolt cutters. I picked up the seal and kept a hole of it to. The port staff opened one door and I opened the other. When the container was opened there was a real stench of petrol inside it. I undid the straps holding the car down. They then had to get a big hammer to move the blocks of wood from behind the wheels as the shippings team had nailed them to the floor so the car couldn't move. They really had done a great job of securing the car.
Before opening the bonnet and jump starting the car I decided to try it and see if it would start. I entered the code, turned the key and she started first time without any problems. There was a bit of a misfire for the first couple of seconds but that soon cleared. The port officials then turned up with a huge ramp on a forklift truck so that we could unload the car.
I reversed the car out of the container and drove it onto the trailer. I noticed at this point that the hydraulic pressure warning light was on telling me that it had low pressure and brake pressure loss warning was displayed on the screen.
I had a look around the car and was immediately blown away by the condition that it was in. You can instantly tell when looking at the car that it's been pampered from day one and has been spoilt rotten. It is stunning and is by far the best XM that I have ever seen. A true credit to it's only owner from new, Harry Boswell. The chaps at the port even commented on the condition saying it was immaculate. We then tied the car down on the trailer and left Grangemouth heading for home.
When we got home I unloaded the car from the trailer and noticed drops of LHM on the trailer floor. I thought that I'd get the car up on the ramp and have a look underneath it to see where the LHM was coming from.
I noticed that the pipe coming from the pressure regulator going to the valve block mounted on the subframe was leaking where the rubber joins the metal part of the pipe. I'm going to go to our local Citroen dealer tomorrow and get one ordered for it so that it's sealed properly again with no leaks. I also noticed a hole in the exhaust that was blowing a fine spray of water out of it whilst it was on the ramp. I presume this was just the condensation in the exhaust.
I took the exhaust off the car and cleaned up around the small hole with a wire brush. It turned into a bigger hole that needed patching. I cut a patch from a piece of steel, cleaned up the edges and had my brother weld it on to the exhaust (he's a much better welder then I am!) so it's completely sealed again now. As my hands were filthy after fabricating the patch and putting the exhaust back on the car I didn't get a picture of the exhaust after it was patched I'm afraid.
I took the car for a quick run up the country lane that we live on tonight and was totally blown away by how quiet it was, how well it drove, and how comfy it was. It's everything that the C6 should be!
As soon as I can get this pipe I'll get the car into the dealer for an MOT. The sooner I can get it MOT'd the sooner I can start the process of getting it back onto UK plates.
I've attached some of the pictures below:
David.